Видео

Tebra, sa četkisama ili bez, šta je bolje?

а какие подшибники

How did you locked the brushes ?

This tool set up is to be used to crimp 3 different sizes of open barrel terminal ends and is incorrectly used in this video ! Using the correct crimpers one crimp will fold the terminal fully when used properly .

Excellent work, what kind of epoxy did you use, JB Weld? Can it be assembled without it? Why cut brushes in the lathe?

Can it be fix

Qual a marca desse alicate

Now to remove it?

How do you install the spring that holds down the brushes?

Majstore , postavi bi jedno retoričko pitanje . Ako bi se snažni anlaser 24 V preradio za konstantan rad - Alu rebrasto kučište , aksijalni provrti kroz njega za protok rashladne tekučine , ventilator za hlađenje . Pored toga ležajevi , pametna elektronska kontrola okretaja . Ako recimo on vuče pri pokretu motora 300 A staviti limit na 250 A pri max broju okretaja . zanima me , dali bi se brzo potršile četkice i eventualno kolektor ? Lijep pozdrav i sretan rad !

iam the iron man

Hey my friend! What is the bearings model?

6.4 FS

Hi, could the starter engine could be the cause for a slow starting 2.0 bkd engine?

Jedna ręką to sobie możesz zwalić konia

🇵🇹🇫🇷impec bon boulot 👍

adamsın reis

👍👍👍

You must be getting paid by the hour. I counted 12 squeezes of the crimper. And even then, it's not right. 😃

Svaka cast majstore, profi rad 💪🏻

Why change it? It seems it does not have clutch inside…how to diagnose a faulty one?

Donde compraste el repuesto de puente de diodos

too many steps and isn't that a female connector, not a spade/fork

How much cost of this tester

You can try my machine ，crimping terminal

That is nou a spade connector. It is a female quick disconnect.

Russian style Kak dlya selskoj nestnosti

Slm bu açıklayıcı bilgiler için teşekkür ederim Regülatör sağlamlık testi nasıl yapabiliriz

Yağı çözdüğünüz sıvıyı nerden bulabilirim teşekkürler

Excellent vid tanks you, but I wish you would use some dissposable gloves when working with all that crap on them !.

Hargadenamu

😂😂😂🤦‍♂️🤦‍♂️🤦‍♂️

Is it ok if I put in an English comment here?

Un mal crimpado al terminar la tarde.

Where can I buy that type of pliers?

номера если можно плиз

Which model of car has its types of ac compresor?

How many Watts is this soldering iron? 🤔

❤❤❤❤❤❤❤طريقة عملك تعجبني كثيرآ ❤❤❤❤يباركك الرب في عملك اريد أن أعرف عن نوعية سائل التنظيف هل هو السيترو مع تقديري وإحترامي لك

⭐ *PromoSM*

This is exactly what I needed thank you!

Good working bro 😊

Postroch kaborch

nice clear video using only basic tools and a soldering iron......also teh detail on removing and replacing teh C ring on teh Bendix shaft was really cool....

❤❤❤❤❤❤أكثر من رائع

Hello. Can you tell me please from what piece could be the sound like rubbing stones?

Did this have a 10mm bolt inside not a torque? I have 2019 308 1.5 bluehdi and I have the tool socket for the spline but inside there is no t10 it’s a 10mm bolt. I can not find any tool to get his off as a 10mm socket will not fit through the spine socket I’m so confused as I’ve never seen a clutch pulley bolted on with a 10mm hex bolt

Good work

That DACTEM is gold!

Thanks for this video. Good job👌